Enterasys 2S4082-25-SYS Instalační příručka Strana 54
- Strana / 108
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Connecting to COM Port for Local Management
4-14 NAC Controller PEP Installation
5. Plugtheotherendofthecableintotheappropriateportontheotherdevice.Somecablesmay
beterminatedattheotherendwithtwoseparateconnectors,oneforeachfiber‐opticstrand.In
thiscase,ensurethatthetransmitfiber‐opticstrandisconnectedtothereceiveportand
the
receivefiber‐opticstrandtothetransmitport.
Connecting to COM Port for Local Management
ThissectiondescribeshowtoinstallaUTPstraight‐throughcablewithRJ45connectorsand
optionaladapterstoconnectaPC,aVTseriesterminal,oramodemtoanEnterasys Networks
moduletoaccessLocalManagement.Thissectionalsoprovidesthepinoutassignmentsofthe
adapters.
What Is Needed
Thefollowingisalistoftheuser‐suppliedpartsthatmaybeneededdependingontheconnection:
•RJ45‐to‐DB9femaleadapter
•UTPstraight‐throughcableterminated atbothendswithRJ45connectors
•RJ45‐to‐DB25femaleadapter
•RJ45‐to‐DB25maleadapter
UsingaUTPstraight‐throughcableandanRJ45
‐to‐DB9adapter,youcanconnectproducts
equippedwithanRJ45COMporttoanIBMorcompatiblePCrunningaVTseriesemulation
softwarepackage.
UsingaUTPstraight‐throughcableandanRJ45‐to‐DB25femaleadapter,youcanconnect
productsequippedwithanRJ45COMporttoa
VTseriesterminalorVTtypeterminalsrunning
emulationprogramsfortheVTseries.
UsingaUTPstraight‐throughcableandanRJ45‐to‐DB25maleadapter,youcanconnectproducts
equippedwithanRJ45COMporttoaHayescompatiblemodemthatsupports9600 baud.
Connecting to an IBM PC or Compatible Device
ToconnectanIBMPCorcompatibledevice,runningtheVTterminalemulation,toan
Enterasys NetworksmoduleCOMport(Figure 4‐12),proceedasfollows:
1. ConnecttheRJ45connectoratoneendoftheUTPstraight‐throughcabletothe
communicationsCOMportontheEnterasys Networksmodule.(TheCOMportis
alsoknown
asaConsoleport.)
2. PlugtheRJ45connectorattheotherendoftheUTPstraight‐throughcableintoan
RJ45‐to‐DB9adapter.
3. ConnecttheRJ45‐to‐DB9adaptertothecommunicationsportontheIBMPC.
4. TurnonthePCandsetthefollowingparametersonyourVT
emulationpackage:
Parameter Setting
Mode 7 Bit Control
Transmit Transmit=9600
Bits Parity 8 Bits, No Parity
Stop Bit 1 Stop Bit
- Enterasys 1
- orcontactEnterasys 5
- (Circuit Modules) 6
- (Circuit Breakers) 6
- VCCI Notice 7
- BSMI EMC Statement — Taiwan 7
- Safety Information 7
- Class 1 Laser Transceivers 7
- Declaration of Conformity 8
- Contents 11
- Chapter 5: Troubleshooting 12
- About This Guide 17
- Related Documents 18
- Typographical Conventions 19
- Commonly Used Acronyms 19
- Getting Help 20
- Introduction 21
- The N1-7C111 Chassis 22
- The NAC Controller PEP 22
- Overview 23
- 1-4 Introduction 24
- 1-6 Introduction 26
- Standards Compatibility 27
- LANVIEW Diagnostic LEDs 27
- 1-8 Introduction 28
- Site Guidelines 29
- Configuration Guidelines 30
- LANVIEW LEDs 30
- Link Aggregation 32
- 10BASE-T Network 32
- 100BASE-TX Network 32
- 1000BASE-T Network 32
- 1000BASE-SX/LX/ELX Network 33
- Order of Installation 36
- Installing the Rubber Feet 37
- N1 7C111 d 39
- Cooling Fans 40
- Required Tools 41
- Preparation 42
- engine o el módulo 42
- Installation 43
- (MGBIC-02) 4 Port slot 44
- Removing the Mini-GBIC 45
- Connecting to the Network 47
- Switches and End User Devices 49
- 2 Other device port 50
- 3 Release tab 52
- What Is Needed 54
- Connecting to a Modem 56
- RJ45 DB9 57
- Completing the Installation 58
- Enterasys Matrix 59
- Troubleshooting 61
- Using LANVIEW 62
- 5-2 Troubleshooting 62
- Table 5-1 LANVIEW LEDs 63
- Troubleshooting Checklist 64
- 5-6 Troubleshooting 66
- 5-8 Troubleshooting 68
- NAC Controller 74
- Setup the VLAN Configurations 84
- Physical Specifications 91
- Environmental Requirements 92
- Regulatory Requirements 92
- Specifications 93
- Specifications (continued) 94
- Item Specification 95
- Regulatory Compliance 100
- Mode Switch Bank Settings 101
- Location of Memory Modules 102
- Removing the DRAM SIMM 105
- Installing the DRAM SIMM 105
- Index-2 108
Související produkty a manuály pro Sítě Enterasys 2S4082-25-SYS
Sítě Enterasys 8000/8600 Specifikace
(142 stránky)
(142 stránky)
Sítě Enterasys 802 Uživatelský manuál
(14 stránky)
(14 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce