Enterasys Matrix E7 Instalační příručka stáhnout pdf (Strana 69)

FLASH Upgrade

Mode Switch Bank Settings and Options B-5

B.3.2 Installing the FLASH Module

To install a FLASH module, refer to Figure B-3 and proceed as follows:

1. With the FLASH module oriented as shown in Figure B-3, insert the FLASH module down

between the connector.

2. Pivot the FLASH module downward so the connector clips align with the two side notches of

the FLASH module and the connector clips lock the FLASH module into place.

Figure B-3 Installing the FLASH

CAUTION: Observe all antistatic precautions when handling sensitive electronic

equipment.

FLASH

Connector

Clip

2504_91

1 2 ... 64 65 66 67 68 69 70 71 72 73 74 75 76

6G302-06 and 6G306-06 1
FCC NOTICE 4
INDUSTRY CANADA NOTICE 4
VCCI NOTICE 4
CLASS A ITE NOTICE 4
SAFETY INFORMATION 5
CLASS 1 LASER TRANSCEIVERS 5
ENTERASYS NETWORKS, INC 6
PROGRAM LICENSE AGREEMENT 6
DECLARATION OF CONFORMITY 8
Contents 9
INSTALLATION 10
TROUBLESHOOTING 10
SPECIFICATIONS 10
GPIM SPECIFICATIONS 11
About This Guide 15
STRUCTURE OF THIS GUIDE 16
RELATED DOCUMENTS 16
GETTING HELP 17
DOCUMENT CONVENTIONS 17
Getting Help 18
Introduction 19
1-2 Introduction 20
1.1 CONNECTIVITY 21
6G302-06 21
6G306-06 21
1.1.1 Options 22
1.3 SMARTTRUNK 23
1.4 REMOTE MONITORING (RMON) 23
1.5 BROADCAST SUPPRESSION 23
1.7 TRAFFIC RATE LIMITING 24
1.8 FLOW CONTROL 25
1.9 GARP SWITCH OPERATION 25
1.10 802.1 PORT PRIORITY 25
1.12 MANAGEMENT 26
1.13 SWITCHING OPTIONS 27
1.14 STANDARDS COMPATIBILITY 27
1.15 LANVIEW DIAGNOSTIC LEDs 27
Network Requirements 29
2.3 1000BASE-SX/LX NETWORK 30
Installation 31
3.1 UNPACKING THE MODULE 32
3.2.1 Side Clip GPIMs 33
3-4 Installation 34
Figure 3-2 GPIM Connectors 34
3.2.2 Locking Bar GPIMs 36
Installation 3-7 37
3-10 Installation 40
3-12 Installation 42
3-14 Installation 44
Installation 3-15 45
3-16 Installation 46
Receive (Rx) 47
Transmit (Tx) 47
3-20 Installation 50
Receive (RX) 51
Transmit (TX) 51
Troubleshooting 53
Using LANVIEW 55
Troubleshooting 4-3 55
4.2 TROUBLESHOOTING CHECKLIST 56
Troubleshooting Checklist 57
Troubleshooting 4-5 57
4-6 Troubleshooting 58
4.3 USING THE RESET BUTTON 59
Specifications 61
A.3 REGULATORY COMPLIANCE 63
B.1 REQUIRED TOOLS 65
B.2 SETTING THE MODE SWITCHES 66
B.3 FLASH UPGRADE 68
FLASH Upgrade 69
GPIM Specifications 71
C.1.2 GPIM-08 Specifications 72
C.3 REGULATORY COMPLIANCE 74

Komentáře k této Příručce

Žádné komentáře

Enterasys Matrix E7 Instalační příručka Strana 69

Komentáře k této Příručce

Související produkty a manuály pro Síťové přepínače Enterasys Matrix E7