Enterasys RoamAbout AP-2000 Instalační příručka

Access Point 2000 Hardware Installation Guide9034063-06ENJOY THE FREEDOM OF WIRELESS NETWORKINGENTERASYS.COM™

Table of Contentsviii 2 Cabling and WiringSelecting a Power Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ixPrefacePurpose of the ManualThis manual describes how to install and set up the RoamAbout Access Point 2000. It also includes problem solving, and

PrefacexDocument ConventionsThe following icons are used in this document:Icon MeaningELECTRICAL HAZARD: Warns against an action that could result in

xiPrefaceAssociated DocumentsThe following table lists the RoamAbout products and information location. The documentation, drivers, and utilities can

PrefacexiiGetting HelpFor additional support related to this device or document, contact Enterasys Networks using one of the following methods:Before

Preparing for Installation 1-1Chapter 1Preparing for InstallationThis chapter describes basic considerations for successfully installing the RoamAbo

Reviewing the Site Requirements1-2 Preparing for InstallationReviewing the Site RequirementsPlease review the site requirements before you install th

Preparing for Installation 1-3Reviewing the Site RequirementsElectrical RequirementsThe Access Point 2000 power and connector specifications are liste

Unpacking and Inspecting1-4 Preparing for InstallationUnpacking and InspectingPhysically inspect all cartons for shipping damage. Report any damage t

Preparing for Installation 1-5Unpacking and InspectingAccess PointVerify that the following components shipped with your Access Point: * Only use UL L

Options1-6 Preparing for InstallationOptionsThe following options are available for the Access Point: Other ConsiderationsEnterasys Networks recommen

Cabling and Wiring 2-1Chapter 2Cabling and WiringThis chapter presents detailed step-by-step procedures to select, configure, and install the correc

Selecting a Power Configuration2-2 Cabling and WiringSelecting a Power ConfigurationThe power configurations available for the Access Point include l

Cabling and Wiring 2-3Remote Power Injector InstallationRemote Power Injector InstallationThe remote power injector provides operating power to the AP

Remote Power Injector Installation2-4 Cabling and WiringUse the following procedure to install the remote power injector.1. If available, use a cable

Cabling and Wiring 2-5Rack Mount Kit InstallationRack Mount Kit InstallationThe rack mount kit allows you to install up to three remote power injector

Power Module Installation2-6 Cabling and WiringPower Module InstallationTo install the 100-240VAC power supply, perform the following steps: 1. Verif

Cabling and Wiring 2-7Selecting the Correct Ethernet Wiring ConfigurationSelecting the Correct Ethernet Wiring ConfigurationIf you have an existing 10

Power and Connector Specifications2-8 Cabling and WiringPower and Connector SpecificationsAccess Point power and connector specifications are listed

Installing the Access Point 3-1Chapter 3Installing the Access PointThis chapter provides the procedures to install the Access Point 2000 and its opt

NOTICEEnterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site withou

Wall/Ceiling Outlet Box Installation3-2 Installing the Access PointWall/Ceiling Outlet Box InstallationFollow the step-by-step procedure below to ins

Installing the Access Point 3-3Wall/Ceiling Outlet Box Installation4. Connect the Ethernet cable. 5. Before installing the metal mounting bracket, mak

Wall/Ceiling Outlet Box Installation3-4 Installing the Access Point8. Install the PC Card:— Position the card as shown below.— Carefully insert the c

Installing the Access Point 3-5Wall/Ceiling Outlet Box Installation9. If you install the optional range extender antenna or outdoor antenna:— Remove t

Wall/Ceiling Outlet Box Installation3-6 Installing the Access Point11. Install the power module/redundant power module, if used.Refer to Power Module

Installing the Access Point 3-7Surface Wallmount InstallationSurface Wallmount InstallationFollow the step-by-step procedure below to install the AP o

Surface Wallmount Installation3-8 Installing the Access Point4. Flatten the metal mounting bracket tab against the bracket, or remove the tab by bend

Installing the Access Point 3-9Surface Wallmount Installation6. Secure the AP to the mounting bracket:— Insert the two AP shoulder screws into the two

Surface Wallmount Installation3-10 Installing the Access Point7. Install the PC Card:— Position the card as shown below.— Carefully insert the card.—

Installing the Access Point 3-11Surface Wallmount Installation8. If you install the optional range extender antenna or outdoor antenna:— Remove the du

NoticeiiFCC NoticeNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FC

Surface Wallmount Installation3-12 Installing the Access Point10. Connect the 10BaseT Ethernet network cable.If you are using the remote power featur

Installing the Access Point 3-13Surface Wallmount Installation13. Secure the cover:— Position the cover over the AP.— Make sure the cover clears the a

Desktop Installation3-14 Installing the Access PointDesktop InstallationTo install the Access Point on a desktop, do the following:1. Make sure the s

Installing the Access Point 3-15Desktop Installation4. Remove the captive screw bracket by removing two screws. 5. Re-install the two screws.6. Insta

Desktop Installation3-16 Installing the Access Point7. Install the PC Card:— Position the card as shown below.— Carefully insert the card.— Press dow

Installing the Access Point 3-17Desktop Installation8. If you install the optional range extender antenna or outdoor antenna:— Remove the dust cover.—

Desktop Installation3-18 Installing the Access Point10. Connect the 10BaseT Ethernet network cable.If you are using the remote power feature, label t

Installing the Access Point 3-19Desktop Installation13. Secure the cover:— Position the cover over the AP.— Make sure the cover clears the antenna plu

Connecting a Device to the Console Port3-20 Installing the Access PointConnecting a Device to the Console PortYou can manage the Access Point using i

Installing the Access Point 3-21Connecting a Device to the Console Porte) In the Port Settings window, enter:— Bits per second: 9600— Data bits: 8— Pa

iiiNoticeENTERASYS NETWORKS, INC.PROGRAM LICENSE AGREEMENTBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,CAREFULLY READ THIS LICENSE AGREEMENT.This

Verifying the Operation of the Access Point3-22 Installing the Access PointVerifying the Operation of the Access PointThe Access Point runs a series

Installing the Access Point 3-23Verifying the Operation of the Access PointTable 3-1: Access Point LED Summary TableName DescriptionPower/System OKL

Verifying the Operation of the Access Point3-24 Installing the Access PointTable 3-2: Access Point LED Patterns = On = Off = Constant b

Installing the Access Point 3-25Configuring the Access PointConfiguring the Access PointIf creating a new wireless network, refer to the RoamAbout 802

Configuring the Access Point3-26 Installing the Access PointUsing the RoamAbout AP Console Port1. Press the <Return> key at the terminal that i

A-1 Appendix AUpgrade and ResetThis appendix describes how to upgrade the RoamAbout Access Point 2000 firmware using the console port or AP Mana

Upgrade FirmwareA-2 Upgrade FirmwareUsing the Console PortFollow this procedure to upgrade the Access Point 2000 from the console port. Do not c

A-3Upgrade Firmware 4. If the remote BootP option was not selected, use the Browse button next to the File field to locate the latest N*.BIN file f

Hardware Reset to Factory DefaultsA-4 Hardware Reset to Factory DefaultsThe RoamAbout Access Point 2000 hardware reset button (labeled S1 on the

A-5Hardware Reset to Factory Defaults 7. Reapply power then press the reset button (S1) on the AP. If an image is not available, the AP waits appro

Noticeiv(v) Remove any copyright, trademark, proprietary rights, disclaimer or warning notice included on or embedded in any part of the Program.3. AP

vNotice7. LIMITATION OF LIABILITY. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, D

Noticevi13. SEVERABILITY. In the event any provision of this Agreement is found to be invalid, illegal or unenforceable, the validity, legality and en

viiContentsPrefacePurpose of the Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .