Enterasys Matrix 4H4283-49 Instalační příručka stáhnout pdf (Strana 93)

Domů
Enterasys
Síťové přepínače
Matrix 4H4283-49
Instalační příručka

Stažení
Sdílet

Sdílení
Přidat do mých příruček
Tisk

100

101

102

Memory Locations and Replacement Procedures

Matrix DFE-Gold Series Modules Installation Guide B-9

Removing the DIMM from 4H4203-72

To remove the existing DIMM, proceed as follows:

1. Locate the DIMM connector on the main PC board. Refer back to Figure B-6.

2. Push the connector arms away from the DIMM, as shown in Figure B-11, enough to

release the DIMM from the connector.

Figure B-10 Installing the DIMM on 4H4282-49

or 4H4283-49

1 Connector arms 3 Connector

2 DIMM memory module 4 DIMM alignment notches (2)

Caution: Observe all antistatic precautions when handling sensitive electronic equipment.

1 2 ... 88 89 90 91 92 93 94 95 96 97 98 ... 101 102

Installation Guide 1
VCCI Notice 5
BSMI EMC Statement — Taiwan 5
Safety Information 6
Class 1 Laser Transceivers 6
Declaration of Conformity 6
Enterasys Networks, Inc 7
Firmware License Agreement 7
Contents 11
Chapter 4: Troubleshooting 12
Appendix A: Specifications 12
About This Guide 15
Structure of This Guide 16
How to Use This Guide 17
Introduction 19
4H4283-49 20
4H4203-72 20
4H4282-49 20
4H4202-72 21
4H4284-49 21
1-4 Introduction 22
1-6 Introduction 24
Management 26
1-8 Introduction 26
Standards Compatibility 27
LANVIEW Diagnostic LEDs 28
1-10 Introduction 28
Network Requirements 29
provide a 30
Installation 31
Unpacking the DFE-Gold Module 32
3-2 Installation 32
Removing the Coverplate 33
Installing the 7G-6MGBIC 33
3-4 Installation 34
Preparation 35
3-6 Installation 36
Removing the Mini-GBIC 37
Module Placement and Rules 38
Example 2 (Figure 3-5, B) 39
Example 3 (Figure 3-5, C) 39
Example 4 (Figure 3-5, D) 39
4 Metal back panel 42
FAST ENET 43
Connecting to the Network 44
3-14 Installation 44
3-16 Installation 46
2 Other device port 47
3-18 Installation 48
4 RJ21 right-angled connector 50
3-22 Installation 52
connector 54
3 Release tab 55
What Is Needed 56
Mode 7 Bit Control 57
Transmit Transmit=9600 57
Bits Parity 8 Bits, No Parity 57
Stop Bit 1 Stop Bit 57
3-28 Installation 58
Connecting to a Modem 59
3-30 Installation 60
RJ45 DB9 61
RJ45 DB25 61
Completing the Installation 62
3-32 Installation 62
Matrix 63
3-34 Installation 64
3-36 Installation 66
Troubleshooting 67
Using LANVIEW 69
4-4 Troubleshooting 70
Table 4-1 LANVIEW LEDs 71
4-6 Troubleshooting 72
Troubleshooting Checklist 73
4-8 Troubleshooting 74
4-10 Troubleshooting 76
Specifications 77
Item Specification 78
A-4 Specifications 80
COM Port Pinout Assignments 83
Regulatory Compliance 84
Standards 84
Mode Switch Bank Settings and 85
Optional Installations 85
Setting the Mode Switches 86
1 Mode switch bank 87
AST ENET 89
1 2 3 90
Removing the DIMM 91
or 4H4283-49 93
DIMM Replacement (4H4202-72) 95
Removing the DRAM SIMM 96
Installing the DRAM SIMM 96
1 DRAM SIMM 3 Connector arms 97

Komentáře k této Příručce

Žádné komentáře

Enterasys Matrix 4H4283-49 Instalační příručka Strana 93

Komentáře k této Příručce

Související produkty a manuály pro Síťové přepínače Enterasys Matrix 4H4283-49