Enterasys 5C105 Instalační příručka Strana 19
- Strana / 78
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
1-1
1
Introduction
This chapter introduces the 5H152-50 and 5H153-50 Fast Ethernet modules.
The 5H152-50 module (Figure 1-1) features 48 10BASE-T/100BASE-TX switched ports
connected through 48 fixed RJ45 front panel connectors. There is also a slot for an optional
5PIM-G02 or 5PIM-G06 gigabit uplink interface.
The 5H153-50 module (Figure 1-1) features 48 10BASE-T/100BASE-TX switched ports
connected through 4 fixed RJ21 front panel connectors. There is also a slot for an optional
5PIM-G02 or 5PIM-G06 gigabit uplink interface.
Each of the fixed front panel ports can operate in either half-duplex or full-duplex mode of
operation, as determined by auto-negotiation. Full-duplex can also be manually configured.
The module ports can be configured to control traffic in several ways, including prioritizing traffic
flow according to protocol type. The module can also be configured to establish 802.1Q Virtual
Local Area Networks (VLANs) and control the flow of frames associated with each VLAN
according to priority and Ether type. Detailed information about VLANs is provided in the
MATRIX E5 Series Modules Local Management User’s Guide.
The module receives power and backplane connectivity when it is inserted into a 5C105 MATRIX
E5 chassis.
Important Notice
Depending on the firmware version used in the module, some features described in this document
may not be supported. Refer to the Release Notes shipped with the module to determine which
features are supported.
- 5H152-50 and 5H153-50 1
- Fast Ethernet Modules 1
- Installation Guide 1
- FCC NOTICE 4
- INDUSTRY CANADA NOTICE 4
- VCCI NOTICE 4
- CLASS A ITE NOTICE 4
- ENTERASYS NETWORKS, INC 6
- PROGRAM LICENSE AGREEMENT 6
- DECLARATION OF CONFORMITY 8
- Contents 9
- INSTALLATION 10
- TROUBLESHOOTING 10
- SPECIFICATIONS 10
- MODE SWITCH BANK SETTINGS 11
- GPIM SPECIFICATIONS 11
- Figure Page 13
- Ta bl e Page 14
- About This Guide 15
- STRUCTURE OF THIS GUIDE 16
- RELATED DOCUMENTS 17
- DOCUMENT CONVENTIONS 17
- GETTING HELP 18
- Introduction 19
- 5H152-50 20
- 5H153-50 20
- 1.1 CONNECTIVITY 21
- 1.1.3 About the Optional GPIM 21
- Table 1-1 GPIM Options 22
- 1.3 PORT TRUNKING 23
- 1.4 REMOTE MONITORING (RMON) 23
- 1.6 FLOW CONTROL 24
- 1.7 802.1p PORT PRIORITY 24
- 1.8 MANAGEMENT 24
- 1.9 SWITCHING OPTIONS 24
- 1.10 STANDARDS COMPATIBILITY 25
- 1.11 LANVIEW DIAGNOSTIC LEDs 25
- Network Requirements 27
- 2.2 10BASE-T NETWORK 28
- 2.3 100BASE-TX NETWORK 28
- Installation 29
- 3.1 UNPACKING THE MODULE 30
- 3.2 INSTALLING OPTIONAL 5PIMs 31
- 3.2.1 Removing the Coverplate 32
- 3.2.2 Installing the 5PIM 33
- 3.3 INSTALLING OPTIONAL GPIMs 34
- 3.3.1 Side Clip GPIMs 35
- Installing Optional GPIMs 36
- 3.3.2 Locking Bar GPIMs 38
- Preparation 38
- 3.5 CONNECTING TO THE NETWORK 43
- Connecting to the Network 44
- Between Switches and End User 45
- RJ21 angle adapter 48
- RJ21 right-angled connector 48
- RJ21 port connector 48
- Retaining clips 48
- Retaining screws 48
- ➃ shown in Figure 3-10 are 49
- 5PIM-G06 50
- Multimode fiber optic Cables 51
- ➀, key side down ➁, into the 52
- SC cable connector 53
- GPIM-01, GPIM-08, or GPIM-09 53
- 5PIM interface module 53
- Troubleshooting 55
- Port 1, Group 1 LEDs 56
- Using LANVIEW 57
- Table 4-1 LANVIEW LEDs 57
- 4.2 TROUBLESHOOTING CHECKLIST 59
- Troubleshooting Checklist 60
- 4.3 USING THE RESET BUTTON 61
- Specifications 63
- A.1.3 Input/Output Ports 64
- A.2 5PIM SPECIFICATIONS 64
- SC fiber optic connection 65
- A.5 REGULATORY COMPLIANCE 66
- Mode Switch Bank Settings 67
- Mode switch bank 68
- • Switch 6 – No function 69
- GPIM Specifications 71
- Refer to 73
- for details 73
- Environmental 74
Grundig Budíky uživatelské příručky
Začínající na M
Komentáře k této Příručce